Hy-Security SwingRiser 14 Installation And Reference Manual Download Page 9

Page: 9 / 86

Installation and Maintenance Manual

HySecurity

Hydraulic Swing Gate Operator

Introduction

Welcome

– We would like to take this opportunity to thank you for this

purchase. HySecurity has manufactured the finest hydraulic gate

operators available since the 1970s. Our commitment to quality and

innovation will become evident as you become familiar with the features

and performance of this expertly engineered machine. All HySecurity

operators are equipped with the Smart Touch Controller, a digital

electronic brain that offers unparalleled features.

Please take a few minutes to study the contents of this instruction manual.

The benefits of taking a little extra time to align the gate operator properly

and to verify a fully functional installation will ensure customer satisfaction

and a longer life with minimal maintenance costs.

Installers and owners must be certain to thoroughly review and

understand the Important Information regarding pedestrian

entrapment protection contained within this manual. There are

hazards associated with automatic gates that can be greatly reduced

with proper design, installation use. When an automatic gate is first

made functional, the installer must teach the owners and users how

to operate this system correctly. When the installation is complete,

leave this man

ual for the owner’s use and reference.

Please do not hesitate to give your HySecurity distributor a call if you

experience any difficulties during the installation. They are experienced

and trained to assist in resolving any problems.

Summary of Contents for SwingRiser 14























































































Search results

Summary of Contents for SwingRiser 14

Reviews:

Related manuals for SwingRiser 14

Brands by name

Popular brands

Hy-Security SwingRiser 14, Installation And Reference Manual

Search results

Summary of Contents for SwingRiser 14

Reviews:

Related manuals for SwingRiser 14

Brands by name

Popular brands