manualshive.com logo in svg

Hy-Security SwingRiser 14, Installation And Reference Manual

Share
Download
Hy-Security SwingRiser 14 Installation And Reference Manual Download Page 27

Installation and Maintenance Manual 

 

17 

 Detailed Installation Instructions for HRG Swing Gate Operator 

 

1)  Mount control box and connect all conduit fittings.  

a)  Mount controller box within 100ft (30m) of the gate operator, preferably within 20ft (6m). If 

installing the DC version of the operator, mount the battery power supply very near the controller 
enclosure because of the high current demand by the DC motor 

– See the Two Part operator 

section.   

b)  Attach all electrical conduits as required, note the diagram below and see step number 3.  

 

 

 

 
 

2)  Mount operator post 

a)  Using four 

⅝-inch to ¾-inch anchor bolts, mount 

the 12-inch square operator base with 1-inch 
clearance between the base and the backing post 
or wall. The gap between the operator post and 
the backing post will be 3½-inches. It is important 
that the finished installation be plumb and true. 
Use shims if necessary to level the operator base. 

b) 

Attach the top of the operator to the backing post 
or supporting wall, using the bracket provided.  
The attaching bracket "sleeves" inside the top of 
the operator post. See page 11 for Top Cap 
Options.

 

NOTE: The backing post/column, (provided by 
others) must accommodate all of the "tip over" 
loads imposed by the gate panel. 

 

Summary of Contents for SwingRiser 14























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands