Hy-Security SwingRiser 14 Installation And Reference Manual Download Page 25 | Manualshive

Page: 25 / 86

background image

Installation and Maintenance Manual

15

Installation Preparation Checklist

1. Read

all

of the instructions, especially the

Important

Information

at the beginning of this manual, before you

attempt installation. This section is focused upon
mechanical installation. For electrical setup, skip to the
section on system configuration and use of the Smart
Touch Controller.

2. Check to see that the mounting slab is the right size and ready to

have an operator attached. Also check that electrical conduits are
correctly located to enter the operator base. HySecurity
recommends the slab reaches below the local frost line and is
poured together with supporting post or pilaster.

NOTE: The backing post/column, (provided by others) must
accommodate all of the "tip over" loads imposed by the gate
panel.

Installation Process Overview

Mount the control box and connect all

conduit fittings.

Mount the operator post.

Install all accessories such as: vehicle

sensing loops, access control devices,
gate edge sensors or photo eyes.

Pull all wires and hoses into conduits.

Note: HRG 220 comes with up to 5

0’ of

hose for the HRG 222 with up to 150’ of
hose, however, you must advise the
factory on the accurate amount of hose
desired or it will not be shipped with the
operator.

Test the basic operator functions.

Mount the gate panel and make fine

adjustments.

«
...
23
24
25
26
27
...
»

Summary of Contents for SwingRiser 14























































































Reviews:

No comments

Related manuals for SwingRiser 14

Brand: Roger Pages: 8

8K01MI-0503 FROG KIT

Brand: CAME Pages: 32

Brand: Hamilton Beach Pages: 10

Brand: Hamilton Beach Pages: 20

Brand: Hamilton Beach Pages: 24

Brand: Haas Door Pages: 14

Brand: CAME Pages: 16

Brand: BETCO Pages: 9

Security+ 3265CM-267

Brand: Chamberlain Pages: 72

Security+ 3265-267CM 1/2 HP

Brand: Chamberlain Pages: 72

Security+ 2595C

Brand: Chamberlain Pages: 64

Security+ 2585C

Brand: Chamberlain Pages: 72

Security+ 3112E

Brand: Chamberlain Pages: 80

Brand: Chamberlain Pages: 148

GDO-9v2 SecuraLift

Brand: Automatic Technology Pages: 36

Brand: Radio Shack Pages: 4

Brand: DITEC Pages: 4

Brand: DITEC Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands