HUSTLER SmoothTrak Super S, Manual, Page: 151 / 432

606834CE 5-1 REV A
CZ
DA
DE
EN
ES
FR
IT
NL
PT
SV
TROUBLESHOOTING
The majority of operating problems that occur with a system can be traced to improper adjustments or delayed service. A
consistently applied preventative maintenance program, as outlined in the Maintenance section of this manual, will prevent many
problems. The following chart is designed to help you locate a problem by suggesting probable causes and the recommended
solutions.
SYMPTOMS PROBABLE CAUSES
SUGGESTED
REMEDIES
Starting motor does not
crank
Park brake lever not in park
brake position
Place park brake lever in
park brake position
Deck clutch switch
engaged
Disengage clutch switch
Weak or dead battery Recharge or replace
Electrical connections are
corroded or loose
Check the electrical
connections
Fuse is blown Check fuses – replace
blown fuse
Neutral switches not
engaging
Move steering control lever
to neutral position or
adjust switches if
necessary
For additional causes See engine manual
The engine will not start,
starts hard or fails to
keep running
No fuel or line plugged Fill tank or replace line
(See Fuel System section
for more details)
Fuel valve is turned off Open the fuel valve
There is incorrect fuel in
the fuel system
Drain the tank and replace
the fuel with the proper
type
There is dirt in the fuel filter Replace the fuel filter
Dirt, water or stale fuel in
the fuel system
Contact your Dealer
The choke is not on
(if equipped)
Move the choke lever to ON
Numerous See engine manual
Engine:
Runs with continuous
misfiring or engine runs
unevenly or erratically
Numerous See engine manual
Loss of power or system
will not operate in either
direction
Restrictions in air cleaner Service air cleaner
Poor compression Contact your Dealer
Steering linkage needs
adjustment
Adjust linkage
Tow valve open Close tow valve
The traction drive belt is
worn, loose or broken
Install a new traction drive
belt
Air in system Check filter and fittings
For additional causes See engine manual
Air cooled engine
overheating
Air intake screen or
cleaning fins clogged
Clean screen and fin
For additional causes See engine manual
Low engine oil pressure Low oil level Add oil
Oil diluted or too light Change oil and check for
source of contamination
Failed oil pump Contact your Dealer
High oil consumption Numerous Contact your Dealer
Mower jerky when
starting or operates in
one direction only
Steering control linkage
needs adjustment
Adjust linkage
Loose steering linkage Tighten linkage
Tow valves not closed
completely
Close tow valves
Pump or wheel motors
faulty
Contact your Dealer
Mower circles or veers in
one direction
Steering linkage needs
adjustment
Adjust linkage
Loose steering linkage Tighten linkage
Tires improperly inflated Adjust air pressure to 55–
83 KPa
Wheel motor faulty Contact your Dealer
Hydraulic pump faulty Contact your Dealer
There is abnormal
vibration
The engine mounting bolts
are loose
Tighten the engine
mounting bolts
The engine pulley, idler
pulley or blade pulley is
loose
Tighten the appropriate
pulley
The engine pulley is
damaged
Contact your Dealer
The cutting blade(s) is/are
bent or unbalanced
Install new cutting blade(s)
A blade mounting bolt is
loose
Tighten the blade
mounting bolt
Spindle bearing is worn or
loose
Replace or tighten spindle
bearing
A blade spindle mount is
bent
Contact your Dealer
Blades do not rotate The deck drive belt is worn,
loose or broken
Install a new deck drive
belt
The deck drive belt is off
the pulley
Install the deck drive belt
and check for a reason
Electric clutch is not
engaging
Check and/or replace 15
amp fuse.
Contact your Dealer
Uneven cutting height The blade(s) are not sharp Sharpen the blades
A cutting blade(s) is/are
bent
Install new cutting blade(s)
The deck is not level Level the deck per the Deck
leveling and height
adjustment section of the
General Service Manual
An anti-scalp wheel is not
set correctly
Adjust the height of the
anti-scalp wheel
The underside of the deck
is dirty
Clean the underside of the
deck
Tires improperly inflated Adjust air pressure to 55–
83 KPa
A blade spindle mount is
bent
Contact your Dealer
SYMPTOMS PROBABLE CAUSES
SUGGESTED
REMEDIES