Huawei 196KTL-H0 User Manual Download

Page: 79 / 122

No.

Parameter

Description

Remarks

Threshold for

triggering

HVRT (V)

Specifies the threshold for triggering HVRT. The

threshold settings should meet the local grid

standard.

This parameter is

displayed when HVRT

is set to Enable.

HVRT

gradient K1

During HVRT, the solar inverter needs to

generate positive-sequence reactive power to

support the power grid. This parameter is used

to set the positive-sequence reactive power

generated by the solar inverter.
For example, if you set HVRT gradient K1 to 2,

the positive-sequence reactive current

generated by the solar inverter is 20% of the

rated current when the AC voltage increases by

10% during HVRT.

HVRT

gradient K2

During HVRT, the solar inverter needs to

generate negative-sequence reactive power to

support the power grid. This parameter is used

to set the negative-sequence reactive power

generated by the solar inverter.
For example, if you set HVRT gradient K2 to 2,

the negative-sequence reactive current

generated by the solar inverter is 20% of the

rated current when the AC voltage increases by

10% during HVRT.

Grid voltage

protection

shield during

VRT

Specifies whether to shield the undervoltage

protection function during LVRT or HVRT.

This parameter is

displayed when LVRT

or HVRT is set to

Enable.

VRT exit

hysteresis

threshold

Specifies the LVRT/HVRT recovery threshold.

● This parameter is

displayed when

LVRT or HVRT is

set to Enable.

● LVRT recovery

threshold =

Threshold for

triggering LVRT +

VRT exit hysteresis

threshold

● HVRT recovery

threshold =

Threshold for

triggering HVRT -

VRT exit hysteresis

threshold

SUN2000-(196KTL-H0, 200KTL-H2, 215KTL-H0)

Series

User Manual

7 Man-Machine Interactions

Issue 07 (2021-07-08)

Summary of Contents for 196KTL-H0



























































































































Search results

Summary of Contents for 196KTL-H0

Reviews:

Related manuals for 196KTL-H0

Brands by name

Popular brands

Huawei 196KTL-H0, User Manual

Search results

Summary of Contents for 196KTL-H0

Reviews:

Related manuals for 196KTL-H0

Brands by name

Popular brands