Huawei 196KTL-H0 User Manual Download Page 3

Page: 3 / 122

About This Document

Overview

This document describes the SUN2000-196KTL-H0, SUN2000-200KTL-H2, and

SUN2000-215KTL-H0 (SUN2000 for short) in terms of their installation, electrical

connections, commissioning, maintenance, and troubleshooting. Before installing

and operating the inverter, ensure that you are familiar with the features,

functions, and safety precautions provided in this document.

Intended Audience

This document is intended for photovoltaic (PV) plant operating personnel and

qualified electricians.

Symbol Conventions

The symbols that may be found in this document are defined as follows.

Symbol

Description

Indicates a hazard with a high level of risk which, if not

avoided, will result in death or serious injury.

Indicates a hazard with a medium level of risk which, if not

avoided, could result in death or serious injury.

Indicates a hazard with a low level of risk which, if not

avoided, could result in minor or moderate injury.

Indicates a potentially hazardous situation which, if not

avoided, could result in equipment damage, data loss,

performance deterioration, or unanticipated results.
NOTICE is used to address practices not related to personal

injury.

Supplements the important information in the main text.
NOTE is used to address information not related to personal

injury, equipment damage, and environment deterioration.

SUN2000-(196KTL-H0, 200KTL-H2, 215KTL-H0)

Series

User Manual

About This Document

Issue 07 (2021-07-08)

Summary of Contents for 196KTL-H0



























































































































Search results

Summary of Contents for 196KTL-H0

Reviews:

Related manuals for 196KTL-H0

Brands by name

Popular brands

Huawei 196KTL-H0, User Manual

Search results

Summary of Contents for 196KTL-H0

Reviews:

Related manuals for 196KTL-H0

Brands by name

Popular brands