Huawei 196KTL-H0 User Manual Download Page 78

Page: 78 / 122

No.

Parameter

Description

Remarks

LVRT gradient

During LVRT, the solar inverter needs to

generate positive-sequence reactive power to

support the power grid. This parameter is used

to set the positive-sequence reactive power

generated by the solar inverter.
For example, if you set LVRT gradient K1 to 2,

the positive-sequence reactive current

generated by the solar inverter is 20% of the

rated current when the AC voltage decreases by

10% during LVRT.

LVRT gradient

During LVRT, the solar inverter needs to

generate negative-sequence reactive power to

support the power grid. This parameter is used

to set the negative-sequence reactive power

generated by the solar inverter.
For example, if you set LVRT gradient K2 to 2,

the negative-sequence reactive current

generated by the solar inverter is 20% of the

rated current when the AC voltage decreases by

10% during LVRT.

Percentage of

LVRT reactive

current

limiting

During LVRT, the solar inverter needs to limit

the reactive current.
For example, if you set Percentage of LVRT

reactive current limiting to 50, the reactive

current upper limit of the solar inverter is 50%

of the rated current during LVRT.

Threshold of

LVRT zero-

current mode

When Zero current due to power grid fault is

enabled, if the power grid voltage is less than

the value of Threshold of LVRT zero-current

mode during LVRT, the zero current mode is

used. Otherwise, the mode configured in LVRT

mode is used.

LVRT mode

Sets LVRT mode. The options are Zero-current

mode, Constant current mode, Reactive

power priority mode, and Active power

priority mode.

LVRT

characteristic

curve

Specifies the low voltage ride-through

capability of the inverter.

HVRT

HVRT is short for high voltage ride-through.

When the grid voltage is abnormally high for a

short time, the inverter cannot disconnect from

the power grid immediately and has to work for

some time.

SUN2000-(196KTL-H0, 200KTL-H2, 215KTL-H0)

Series

User Manual

7 Man-Machine Interactions

Issue 07 (2021-07-08)

Summary of Contents for 196KTL-H0



























































































































Search results

Summary of Contents for 196KTL-H0

Reviews:

Related manuals for 196KTL-H0

Brands by name

Popular brands

Huawei 196KTL-H0, User Manual

Search results

Summary of Contents for 196KTL-H0

Reviews:

Related manuals for 196KTL-H0

Brands by name

Popular brands