Huawei 196KTL-H0 User Manual Download Page 104

Page: 104 / 122

Alarm

Alarm Name

Alarm

Severity

Cause

Troubleshooting Suggestions

2038

Unstable Grid

Frequency

Major

Cause ID=1
Power grid exception: The

actual grid frequency

change rate does not

comply with the local

power grid standard.

1. If the alarm occurs

occasionally, the power grid

may be abnormal

temporarily. The inverter

automatically recovers after

detecting that the power

grid becomes normal.

2. If the alarm occurs

frequently, check whether

the power grid frequency is

within the acceptable

range. If not, contact the

local power operator.

2039

Output

Overcurrent

Major

Cause ID=1
The power grid voltage

drops dramatically or the

power grid is short-

circuited. As a result, the

inverter transient output

current exceeds the upper

threshold and therefore

the inverter protection is

triggered.

1. The inverter detects its

external working conditions

in real time. After the fault

is rectified, the inverter

automatically recovers.

2. If the alarm occurs

frequently and affects the

energy yield of the power

plant, check whether the

output is short-circuited. If

the fault cannot be

rectified, contact your

dealer or Huawei technical

support.

2040

Output DC

Component

Overhigh

Major

Cause ID=1
The DC component of the

inverter output current

exceeds the specified

upper threshold.

1. If the exception is caused by

an external fault, the

inverter automatically

recovers after the fault is

rectified.

2. If this alarm occurs

frequently and affects the

energy yield of the PV

plant, contact your dealer

or Huawei technical

support.

SUN2000-(196KTL-H0, 200KTL-H2, 215KTL-H0)

Series

User Manual

8 Maintenance

Issue 07 (2021-07-08)

Summary of Contents for 196KTL-H0



























































































































Search results

Summary of Contents for 196KTL-H0

Reviews:

Related manuals for 196KTL-H0

Brands by name

Popular brands

Huawei 196KTL-H0, User Manual

Search results

Summary of Contents for 196KTL-H0

Reviews:

Related manuals for 196KTL-H0

Brands by name

Popular brands