Huawei 196KTL-H0 User Manual Download Page 42

Page: 42 / 122

5.4 (Optional) Replacing the Crimping Module

Procedure

NO TE

If the AC output power cable has a single core, replace the crimping module.

Step 1 Replace the crimping module.

Figure 5-6 Replacing the crimping module

----End

5.5 (Optional) Installing the Power Cable of the

Tracking System

Precautions

NO TICE

● A switch-disconnector-fuse or fuse-switch-disconnector with a voltage of no

less than 800 V, current of 16 A, and protection type of gM needs to be

installed between the inverter and the tracker controller for protection.

● The cable between the wiring terminal on the power cable and the switch-

disconnector-fuse or fuse-switch-disconnector should be less than or equal to

2.5 m.

● Connect the power cable of the tracking system before the AC output power

cable. Otherwise, reworking will be caused.

SUN2000-(196KTL-H0, 200KTL-H2, 215KTL-H0)

Series

User Manual

5 Electrical Connections

Issue 07 (2021-07-08)

Summary of Contents for 196KTL-H0



























































































































Search results

Summary of Contents for 196KTL-H0

Reviews:

Related manuals for 196KTL-H0

Brands by name

Popular brands

Huawei 196KTL-H0, User Manual

Search results

Summary of Contents for 196KTL-H0

Reviews:

Related manuals for 196KTL-H0

Brands by name

Popular brands