Huawei 196KTL-H0 User Manual Download Page 69

Page: 69 / 122

Figure 7-9 Feature parameters (advanced user)

----End

Parameters

No.

Parameter

Description

Remarks

MPPT multi-peak

scanning

When the inverter is used in

scenarios where PV strings are

greatly shaded, set this parameter

to Enable, and then the inverter

will perform MPPT scanning at

regular intervals to locate the

maximum power.

MPPT multi-peak

scan interval (min)

Specifies the MPPT scanning

interval.

This parameter is displayed

when MPPT multi-peak

scanning is set to Enable.

RCD enhancement

RCD refers to the residual current

of the inverter to the ground. To

ensure device and personal safety,

RCD should be limited to the

specified value in the standard. If

an AC switch with a residual

current detection function is

installed outside the inverter, this

function should be enabled to

reduce the residual current

generated when the inverter is

running, thereby preventing the

AC switch from misoperations.

SUN2000-(196KTL-H0, 200KTL-H2, 215KTL-H0)

Series

User Manual

7 Man-Machine Interactions

Issue 07 (2021-07-08)

Summary of Contents for 196KTL-H0



























































































































Search results

Summary of Contents for 196KTL-H0

Reviews:

Related manuals for 196KTL-H0

Brands by name

Popular brands

Huawei 196KTL-H0, User Manual

Search results

Summary of Contents for 196KTL-H0

Reviews:

Related manuals for 196KTL-H0

Brands by name

Popular brands