Huawei 196KTL-H0 User Manual Download Page 28

Page: 28 / 122

Type

Tool

Hydraulic pliers

Heat shrink tubing

Heat gun

Binding strap

Personal

protective

equipment

(PPE)

Safety gloves

Safety goggles

Anti-dust

respirator

Safety boots

4.3 Determining the Installation Position

4.3.1 Environment Requirements

Basic Requirements

●

Do not install the inverter in working or living areas.

●

If the device is installed in public places (such as parking lots, stations, and

factories) other than working and living areas, install a protective net outside

the device, set up a safety warning sign to isolate the device, and prevent

unauthorized personnel from approaching the inverter. This is to avoid

personal injury or property loss caused by accidental contact or other reasons

during device operation.

●

Do not install the inverter in areas with flammable materials.

●

Do not install the inverter in areas with explosive materials.

●

Do not install the inverter in areas with corrosive materials.

●

Do not install the inverter where its enclosure and heat sinks are easily

accessible, because the voltage is high and these parts are hot during

operation.

●

Install the inverter in a well-ventilated environment for heat dissipation

●

If the inverter is installed in an airtight environment, a heat dissipation device

or ventilation device must be installed to ensure that the indoor ambient

temperature is not higher than the external ambient temperature during

operation.

●

You are advised to install the inverter in a sheltered place or install an awning

over it.

●

The inverter will be corroded in salt areas. Before installing the inverter

outdoors in salt areas, consult Huawei. A salt area refers to the region within

SUN2000-(196KTL-H0, 200KTL-H2, 215KTL-H0)

Series

User Manual

4 Installation

Issue 07 (2021-07-08)

Summary of Contents for 196KTL-H0



























































































































Search results

Summary of Contents for 196KTL-H0

Reviews:

Related manuals for 196KTL-H0

Brands by name

Popular brands

Huawei 196KTL-H0, User Manual

Search results

Summary of Contents for 196KTL-H0

Reviews:

Related manuals for 196KTL-H0

Brands by name

Popular brands