manualshive.com logo in svg

HP ZBook Studio G 315-ap000 - 15ap099, Maintenance And Service Manual, Page: 71 / 185

Share
Download
HP ZBook Studio G 315-ap000 - 15ap099 Maintenance And Service Manual Download Page 71

b.

Disconnect the module cable (2) from the module.

c.

Remove the module.

The webcam module is available using spare part number 840965-001.

The microphone module is available using spare part number 840955-001.

7.

If it is necessary to replace the thermal board:

a.

Disconnect the thermal board cable (1) from the board.

b.

Using a flat tool, pry the board loose (2), and then remove the board (3) from the display 
enclosure. (The thermal board is attached to the display enclosure with double-sided adhesive.)

c.

Remove the thermal board.

The thermal board is available using spare part number 840956-001.

8.

If it is necessary to replace the display hinges:

a.

Remove the three Torx T8M2.5×4.0 screws (1) that secure each display hinge to the display panel.

Component replacement procedures

57

Summary of Contents for ZBook Studio G 315-ap000 - 15ap099


























































































































































































Reviews:

No comments