manualshive.com logo in svg

HP ZBook Studio G 315-ap000 - 15ap099, Maintenance And Service Manual

Share
Download
HP ZBook Studio G 315-ap000 - 15ap099 Maintenance And Service Manual Download Page 125

Speaker, headphone - audio issues

 

 

Symptoms

●

No sound from external or 
internal speakers

●

Distorted sound, too soft, too 
loud, intermittent

Possible causes

Volume turned down, sound card not recognized, malfunctioning hardware, electronic 
interference.

 

Troubleshooting steps

1.

Remove any device connected to the Audio jack to enable the internal speaker.

2.

Close all open programs.

3.

Adjust volume by pressing 

Fn + F6/F7

. Be sure that volume button light is not amber 

(mute).

- or -

Adjust Windows volume control by clicking the speaker icon on the Windows taskbar. Be 
sure that the sound is not muted.

4.

Verify that sound card is detected in Windows Device Manager.

5.

Reinstall the latest audio driver.

6.

Test audio device using HP PC Hardware Diagnostics (UEFI) tool (

F2

 > Component Tests 

> Audio).

7.

Test with a verified working operating system. If issue is resolved, restore full operating 
system.

8.

Test with verified working external speakers or headset.

9.

Reseat internal speaker connections.

10.

Test with verified working internal speakers.

11.

Replace internal speakers.

No sound from headphones

1.

Adjust volume by pressing 

Fn + F6/F7

. Be sure that volume button light is not amber 

(mute). Or adjust Windows volume control by clicking the speaker icon on the Windows 
taskbar. Be sure that the sound it not muted.

2.

Check headphone cable connection.

3.

Test with a verified working audio board.

4.

Replace audio board and verify the change.

No sound from external speakers

1.

Verify that external speakers are turned on.

2.

Disconnect headphones from headphone jack.

3.

Adjust volume by pressing 

Fn + F6/F7

. Be sure that volume button light is not amber 

(mute).

- or -

Adjust Windows volume control by clicking the speaker icon on the Windows taskbar. Be 
sure that the sound is not muted.

4.

Check for possible interference devices nearby that may impact the audio (cell phone or 
portable communications handset.)

Common issues and possible solutions 111

Summary of Contents for ZBook Studio G 315-ap000 - 15ap099


























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands