manualshive.com logo in svg

HP ZBook Studio G 315-ap000 - 15ap099, Maintenance And Service Manual, Page: 17 / 185

Share
Download
HP ZBook Studio G 315-ap000 - 15ap099 Maintenance And Service Manual Download Page 17

Category

Description

WPAN

Bluetooth® 4.1 only supported via combo card

External media cards

Integrated SD UHS-II flash media slot

Supports next generation SD, SDHC, SDXC

Ports

●

Multi-Pin AC Port

●

Combination mic-in/stereo headphone jack

●

RJ-45 (Ethernet)

●

USB Type-C Thunderbolt

●

USB 3.0 (2)

●

USB 3.0 charging (1)

●

HDMI

Docking

Docking support for HP Advanced Docking Station

Keyboard/pointing devices

Keyboard

Backlit

DuraKeys

TouchPad

●

On/off button

●

Glass with chemical etched surface

●

Taps enabled by default

●

Gestures enabled by default:

◦

2-finger scrolling

◦

2-finger zoom (pinch)

●

Image sensor TouchPad

Power requirements

AC adapter

●

150-W, HP Smart Adapter, slim

Battery

●

4-cell, 64-WHr, 4.21-AHr, Li-ion battery

Power cord (localized)

3-wire plug, 1.8 m (with ground pin)

Security

Support security lock

Trusted platform module (TPM) 9760 1.2/2.0 (Infineon; soldered down)

Fingerprint reader

BIOS Preboot power on - BIOS option (Password, Fingerprint)

Drive Encryption preboot option (fingerprint, password, smart card)

Operating system

Preinstalled:

●

Windows 10 Home 64

3

Summary of Contents for ZBook Studio G 315-ap000 - 15ap099


























































































































































































Reviews:

No comments