manualshive.com logo in svg

HP ZBook Studio G 315-ap000 - 15ap099, Maintenance And Service Manual, Page: 108 / 185

Share
Download
HP ZBook Studio G 315-ap000 - 15ap099 Maintenance And Service Manual Download Page 108

 

Troubleshooting steps

Follow suggested steps below one at a time to verify normal boot process:

1.

Disconnect all external peripherals, and perform a hard reset (

8. Hard reset 

on page 74

).

2.

Perform soft reset (

9. Soft reset (Default Settings) on page 75

).

3.

Update BIOS and drivers (

4. Update BIOS and drivers on page 66

).

a.

Roll back to previous version may be necessary.

b.

Go to safe mode to install drivers.

4.

Run Hardware Diagnostics (

6. HP Hardware Diagnostics and Tools on page 67

) 

to isolate hardware issue.

5.

Undo recent changes in Windows (

5. Remove or uninstall recently added 

hardware, software on page 66

).

6.

Reseat cables and connections (

10. Reseat cables and connections 

on page 75

).

7.

Start Windows in safe mode (

11. Test with minimum configuration

 

on page 76

).

8.

Use Startup Repair Windows to fix Windows damaged files.

9.

Test with essential hardware configuration (

11. Test with minimum 

configuration on page 76

) along with a verified working operating system (i.e., 

USB Windows-To-Go ) if available to isolate the software issue.

Tips and tricks

For more information, see 

HP PCs - Using Task Manager (Windows 10, 8)

.

Electromagnetic Interference (EMI)

 

 

Symptoms

System locks up, freezes in certain 
physical area or location

Possible causes

Electromagnetic interference (EMI).

Troubleshooting steps

1.

See (

2. Examine the environment on page 65

). Pay attention to external power source, 

high-frequency signals such as cell phones, microwave ovens.

2.

Move the computer to different locations nearby to determine where it fails and where it 
does not fail.

3.

Test with a verified working computer in original factory configuration.

4.

Consult with support.

94

Chapter 7   Troubleshooting guide

Summary of Contents for ZBook Studio G 315-ap000 - 15ap099


























































































































































































Reviews:

No comments