manualshive.com logo in svg

HP ZBook Studio G 315-ap000 - 15ap099, Maintenance And Service Manual, Page: 19 / 185

Share
Download
HP ZBook Studio G 315-ap000 - 15ap099 Maintenance And Service Manual Download Page 19

2

External component identification

Display

Component

Description

(1)

WLAN antennas* (select products only)

Send and receive wireless signals to communicate with wireless local 
area networks (WLANs).

(2)

Internal microphones (2) (select products only)

Record sound.

(3)

Webcam light (select products only)

On: The webcam is in use.

(4)

Webcam (select products only)

Records video and captures photographs. Some models allow you to 
video conference and chat online using streaming video.

To use the webcam in Windows 10:

▲

Type 

camera

 in the taskbar search box, and then select 

Camera.

For information on using the webcam in Windows 7, select Start > All 
Programs > Communication and Chat > HP WebCam.

*The antennas are not visible from the outside of the computer. For optimal transmission, keep the areas immediately around the 
antennas free from obstructions.

For wireless regulatory notices, see the section of the Regulatory, Safety, and Environmental Notices that applies to your country or 
region.

To access this guide in Windows 10:

1.

Type 

support

 in the taskbar search box, and then select the HP Support Assistant app.

‒

 or –

Display

5

Summary of Contents for ZBook Studio G 315-ap000 - 15ap099


























































































































































































Reviews:

No comments