HP OMNIBOOK 3000 Service Manual Download Page 35

Page: 35 / 86

HP OmniBook 3000

Removal and Replacement

2-17

Figure 2-14. Removing the Keyboard

Reassembly Notes

•

After connecting the keyboard flex cable, insert the front edge of the keyboard into the front slots,
then slide it back. Make sure it is underneath the four plastic tabs along the back edge.

•

Slide the open end of the hinge cover onto the hinge, then lift the closed end over the bump and slide
it in.

Removing the Top Case and TouchPad

(HP Authorized Service Providers Only)

Required Equipment

•

Small Phillips screwdriver, preferably magnetized.

Removal Procedure

1. Unplug the ac adapter, if present, and remove the battery.

2. Remove these additional assemblies:

•

Floppy drive or other plug-in module (see page 2-3).

•

Hard drive (see page 2-4).

Screw, M2.5×

3mm

F1391-60955 (2)

Keyboard flex cable
(part of the keyboard)

Summary of Contents for OMNIBOOK 3000























































































Search results

Summary of Contents for OMNIBOOK 3000

Reviews:

Related manuals for OMNIBOOK 3000

Brands by name

Popular brands

HP OMNIBOOK 3000, Service Manual

Search results

Summary of Contents for OMNIBOOK 3000

Reviews:

Related manuals for OMNIBOOK 3000

Brands by name

Popular brands