HP OMNIBOOK 3000 Service Manual Download Page 36

Page: 36 / 86

2-18

Removal and Replacement

HP OmniBook 3000

•

Display assembly (see page 2-8).

•

Keyboard (see page 2-11).

3. Remove the heat sink assembly by doing the following:

•

Remove the three

recessed

screws from the heat sink assembly.

Note:

not

remove the two middle screws from the heat sink assembly. They hold a

permanent part of the assembly.

•

Using your fingers or a small flat-blade screwdriver, press the heat sink assembly toward the
back of the computer until the three tabs along the front edge are free from the case.

•

Disengage the front edge, then lift the right end of the assembly and unplug the fan cable from
the motherboard.

Figure 2-15. Removing the Heat Sink Assembly

Screw,

×5mm

F1391-60954 (3)

Note:

Smaller diameter

Heat Sink Assembly
F1391-60921
(includes fan/cable)

Fan cable
connector

Speaker/TouchPad
cable

CPU Thermal Kit (gasket and spacer)
F1391-60917

Do not remove
these two screws.

Summary of Contents for OMNIBOOK 3000























































































Search results

Summary of Contents for OMNIBOOK 3000

Reviews:

Related manuals for OMNIBOOK 3000

Brands by name

Popular brands

HP OMNIBOOK 3000, Service Manual

Search results

Summary of Contents for OMNIBOOK 3000

Reviews:

Related manuals for OMNIBOOK 3000

Brands by name

Popular brands