HP OMNIBOOK 3000 Service Manual Download Page 34

Page: 34 / 86

2-16

Removal and Replacement

HP OmniBook 3000

Removing the Keyboard

(HP Authorized Service Providers Only)

Required Equipment

•

Small Phillips screwdriver, preferably magnetized.

Removal Procedure

1. Unplug the ac adapter, if present, and remove the battery.

2. Remove the floppy drive or other plug-in module (see page 2-3).

3. Open the display fully.

4. Slide off the two plastic hinge covers about 5 mm, then lift them off. Use your finger or a small tool

to push outward next to the hinge.

5. Pry out and pop up the right end of the icon window cover at the plug-in module slot, then pop off

the cover.

Figure 2-13. Removing the Hinge Covers and Icon Window Cover

6. Remove the two screws at the top ends of the keyboard.

7. Slide the keyboard toward the front of the computer until the top edge of the keyboard releases from

the four plastic lugs at the top.

8. Being careful of the flex cable underneath, slide the keyboard toward the front of the computer, then

lift the top edge and pivot the keyboard onto the palmrest.

9. Release the flex cable from the motherboard by lifting the locking tab.

Icon Window Cover
F1391-60928

Hinge Cover
F1391-60935 (2)

Summary of Contents for OMNIBOOK 3000























































































Search results

Summary of Contents for OMNIBOOK 3000

Reviews:

Related manuals for OMNIBOOK 3000

Brands by name

Popular brands

HP OMNIBOOK 3000, Service Manual

Search results

Summary of Contents for OMNIBOOK 3000

Reviews:

Related manuals for OMNIBOOK 3000

Brands by name

Popular brands