manualshive.com logo in svg

HP OMNIBOOK 3000, Service Manual

Share
Download
HP OMNIBOOK 3000 Service Manual Download Page 60

3-12

Troubleshooting and Diagnostics

HP OmniBook 3000

14

1

25

13

6

1

9

5

 Figure 3-3. Serial and Parallel Loopback Connectors

Interpreting the Results

 • 

The following table lists test groups, error codes, and suggestions for followup actions. Consider
these suggestions in combination with other troubleshooting information.

 Table 3-3. OmniBook Diagnostic Error Codes

Code

Suggestions

System Test

0001h -
0008h

Reseat or replace the CPU module.

0009h

Replace the motherboard.

0010h -
002Fh

Reseat or replace the CPU module.

0030h -
0040h

Replace the motherboard.

0041h

Unrecognized interrupts. Run BIOS Setup
and check IRQ assignments for all
devices.

0050h -
0070h

Replace the motherboard.

0071h

Bad CMOS checksum. Reset the system,
then run BIOS Setup and check settings.
Replace motherboard.

0072h

Configuration mismatch in CMOS. Reset
the system, then run BIOS Setup and
check settings. Replace motherboard.

0073h

Bad CMOS RAM size. Reset the system,
then run BIOS Setup and check settings.
Replace motherboard.

0074h

Bad CMOS time. Reset the system, then
run BIOS Setup and check settings.
Replace motherboard.

0075h -
0076h

Reset the system. Replace the
motherboard.

0077h

Replace the motherboard.

0078h

Bad CMOS checksum. Reset the system,
then run BIOS Setup and check settings.
Replace motherboard.

0079h

Replace the motherboard.

0080h -
0082h

No repair. (EISA not supported.)

0083h -
0086h

Replace the system BIOS IC. Replace the
motherboard.

0087h

Replace the motherboard.

Code

Suggestions

0088h -
0090h

Replace the system BIOS IC.

0091h -
009Eh

Replace the system BIOS IC. Replace the
motherboard.

009Fh

Insufficient DOS memory. Load fewer
device drivers.

00A0h -
00A3h

Replace the system BIOS IC. Replace the
motherboard.

00A4h -
00A6h

Replace the system BIOS IC.

00A7h

Replace the system BIOS IC. Replace the
motherboard.

00C3h -
00CCh

Replace the CPU module.

00FFh

Rerun the test. (Possible diagnostic
programming error.)

1000h -
100Dh

No repair. (Single processor.)

1030h -
1031h

Remove RAM boards, then rerun the test.
Replace the CPU module. Replace the
motherboard.

1081h

Replace the CPU module.

1082h

Change the configuration setting for
HIMMEM.SYS to leave a portion of
extended memory for the timer test.

1083h

Have at least 1 MB of memory free, then
rerun this test.

1301h

Run BIOS Setup and enable USB.
Replace the system BIOS IC. Replace the
motherboard.

1302h -
1316h

Replace the motherboard.

1401h

Reprogram or replace the system BIOS
IC. Replace the motherboard.

1402h

Replace the motherboard.

These connections
are not used.

Summary of Contents for OMNIBOOK 3000























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands