manualshive.com logo in svg

HP OMNIBOOK 3000, Service Manual

Share
Download
HP OMNIBOOK 3000 Service Manual Download Page 45

HP OmniBook 3000

Removal and Replacement

2-27

Removing Other Components

(HP Authorized Service Providers Only)

The following table lists additional replaceable components and the removal procedures required to
access them.

 Table 2-6. Other Replaceable Components (Authorized Providers)

Component

Equipment

Removal Procedures

Special Notes

AC Adapter

No repairable components.
Replacement is required.

Audio Jack Holder

Phillips screwdriver,
5 mm hex driver

Plug-in module (page 2-3).
Hard drive (page 2-4).
Display (page 2-8).
Keyboard (page 2-11).
Top case (page 2-17).
Motherboard (page 2-20).

Remove the motherboard
only far enough to slip the
holder off the audio jacks.

Audio PCA

Phillips screwdriver,
5 mm hex driver

Plug-in module (page 2-3).
Hard drive (page 2-4).
Display (page 2-8).
Keyboard (page 2-11).
Top case (page 2-17).
Motherboard (page 2-20).

Unplug audio PCA from
underside of motherboard.
Check that two rubber
bumpers are present on the
new audio PCA directly
behind the two connectors.

CPU Module

Phillips screwdriver

Plug-in module (page 2-3).
Hard drive (page 2-4).
Display (page 2-8).
Keyboard (page 2-11).
Top case (page 2-17).

Remove two screws from
CPU module. Unplug CPU
module from motherboard.

Caution: 

Install both parts of

a CPU thermal kit (F1391-
60917) to the new module.
Stick the gasket to the top of
the CPU. Stick the rubber
spacer to the top back-right
corner of the board.

Display Latch or
Spring

Phillips screwdriver

Plug-in module (page 2-3).
Hard drive (page 2-4).
Display (page 2-8).
Keyboard (page 2-11).
Top case (page 2-17).

To remove, lift the left corner.
To install, put the spring on
the latch shaft, then insert the
shaft through the opening at
the bottom of the right-hand
slot.

Hinge

Phillips screwdriver

Plug-in module (page 2-3).
LCD module, but only until
the display bezel is
removed (page 2-11).

Caution: 

If the display is

attached to the bottom case,
install one new hinge before
you remove the other to avoid
stressing the cables.
Install the hinge so the slit in
the housing faces into the
display case.

Icon/MB Cable

Phillips screwdriver

Plug-in module (page 2-3).
Display, but only until the
icon PCA is removed
(page 2-8).

The display does not have to
be removed.

Summary of Contents for OMNIBOOK 3000























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands