HP OMNIBOOK 3000 Service Manual Download Page 70

Page: 70 / 86

3-22

Troubleshooting and Diagnostics

HP OmniBook 3000

Resume on Time of Day

Sets whether the system resumes from Suspend at a defined
time of day.

Disabled

Resume Time

Sets the 24-hour time when the system resumes from
Suspend if enabled.

Boot Menu

Default

Diskette Drive
Hard Drive
CD-ROM Drive

Shows the order of boot devices. Move the entries to
change the order.

1. Diskette drive
2. Hard drive
3. CD-ROM drive

Exit Menu

Save Changes and Exit

Saves Setup changes, exits, and reboots.

Discard Changes and Exit

Discards Setup changes since last save, exits, and reboots.

Get Default Values

Restores all default settings, and stays in Setup.

Load Previous Values

Discards Setup changes since last save, and stays in Setup.

Save Changes

Saves Setup changes, and stays in Setup.

Summary of Contents for OMNIBOOK 3000























































































Search results

Summary of Contents for OMNIBOOK 3000

Reviews:

Related manuals for OMNIBOOK 3000

Brands by name

Popular brands

HP OMNIBOOK 3000, Service Manual

Search results

Summary of Contents for OMNIBOOK 3000

Reviews:

Related manuals for OMNIBOOK 3000

Brands by name

Popular brands