HP OMNIBOOK 3000 Service Manual Download Page 10 | Manualshive

Page: 10 / 86

background image

1-4

Product Information

HP OmniBook 3000

Checking the Status of the OmniBook

The OmniBook status panel, located above the keyboard (on the icon PCA), contains indicators that
show the current status of the OmniBook. The indicators in the status panel show keyboard status, drive
status, and power status.

Table 1-4. Status Panel Indicators (Icon PCA)

Indicator

Meaning

AC power.

The ac adapter is plugged in.

Blinks

when the battery is being charged.

Battery status.

Shows the approximate charge level of the battery relative to a full

charge. Each bar represents a 10% charge.
The upper and lower triangles indicate the presence of main (upper) and secondary
(lower) batteries. A triangle blinks when that battery is in use. The main battery
charges first, discharges last.
If two batteries are installed and the ac adapter is connected, the indicator shows the
level of the battery being charged. If the ac adapter is not connected, indicator shows
the combined charge of both batteries. Press Fn+F6 to show separate battery levels.

Battery low.

The outline blinks when the battery charge is critically low. The

OmniBook also beeps.

Defective battery.

No battery activity; no charging.

Overheated battery.

The battery is too hot to charge.

CD-ROM drive or hard disk drive.

The OmniBook is accessing one of these built-in

drives.

Floppy disk drive.

The OmniBook is accessing the floppy disk drive.

PC Card.

There is activity between the PC Card and the computer.

(scrolling)

Suspend mode.

These symbols flash from left to right when the OmniBook is

suspended (turned off by pressing the power button briefly).
If ac power is not connected, the green power light also blinks slowly.

Caps Lock.

Caps Lock is active.

Num Lock.

Num Lock is active (Fn+F9).

Keypad Lock.

The built-in embedded keypad is active (Fn+F8). Num Lock must also

be on for the numeric keys.

Scroll Lock.

Scroll Lock is active (Fn+F10).

The green power light (located on the icon PCA) indicates the power state. The green lights on the main
battery or secondary battery indicate its charge level.

Table 1-5. Indicator Lights

Light

Meaning

Power Light

Steady green light
Blinking light

No light

Battery is charging.
Battery is not charging (ac power connected), or
computer is Suspended (no ac power).
Battery is not charging (no ac power).

Battery Lights

Show battery charge level only while the button is pressed on the battery.

«
...
8
9
10
11
12
...
»

Summary of Contents for OMNIBOOK 3000























































































Reviews:

No comments

Related manuals for OMNIBOOK 3000

VisionBook N15G Plus

Brand: UMAX Technologies Pages: 44

Brand: Panasonic Pages: 80

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 13

Brand: Panasonic Pages: 4

Brand: Panasonic Pages: 36

Brand: Panasonic Pages: 112

Brand: Panasonic Pages: 40

Brand: Panasonic Pages: 192

Toughbook CF-T7BWATAAM

Brand: Panasonic Pages: 44

Toughbook CF-F8EWDZZAM

Brand: Panasonic Pages: 20

Toughbook CF-19CHBAXBM

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 40

The Toughbook 52

Brand: Panasonic Pages: 2

MES ACURAS HEAD

Brand: Barco Pages: 131

Brand: Ecco Pages: 4

DWSC - Vintage C

Brand: Daikin Pages: 57

Brand: Lamtec Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands