manualshive.com logo in svg

HP OMNIBOOK 3000, Service Manual

Share
Download
HP OMNIBOOK 3000 Service Manual Download Page 21

HP OmniBook 3000

Removal and Replacement

2-3

Removing the Main Battery

(User-Replaceable)

The main battery is located under the right corner of the palmrest. To remove a secondary battery (an
accessory plug-in module), see the next topic below.

 WARNING

 Do not mutilate, puncture, or dispose of batteries in fire. A battery can burst or explode,
releasing hazardous chemicals. A rechargeable battery must be recycled or disposed of
properly.

Required Equipment

 • 

None.

Removal Procedure

 1. Slide the safety latch for the battery compartment into its recess.

 2. Slide and hold the release latch, then slide out the battery.

 

 

 Figure 2-1. Removing the Main Battery

Reassembly Note

 Caution

 Be sure the safety latch is open before you insert the battery. Otherwise, the release latch could
break if you force the battery in.

 • 

After installing the battery, close the safety latch.

Main Battery
F1382-60901

Summary of Contents for OMNIBOOK 3000























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands