HP OMNIBOOK 3000 Service Manual Download Page 29

Page: 29 / 86

HP OmniBook 3000

Removal and Replacement

2-11

Removing the LCD Module

(HP Authorized Service Providers Only)

Required Equipment

•

Small Phillips screwdriver, preferably magnetized.

•

Pointed knife or probe.

Removal Procedure

1. Unplug the ac adapter, if present, and remove the battery.

2. Remove the floppy drive or other plug-in module (see page 2-3).

3. Open the display fully.

4. Slide off the two plastic hinge covers about 5 mm, then lift them off. Use your finger or a small tool

to push outward next to the hinge.

5. Pry out and pop up the right end of the icon window cover at the plug-in module slot, then pop off

the cover.

Figure 2-9. Removing the Hinge Covers and Icon Window Cover

6. Pry off the two screw covers by the display hinges (use a pointed knife or probe), then remove the

two screws.

Icon Window Cover
F1391-60928

Hinge Cover
F1391-60935 (2)

Summary of Contents for OMNIBOOK 3000























































































Search results

Summary of Contents for OMNIBOOK 3000

Reviews:

Related manuals for OMNIBOOK 3000

Brands by name

Popular brands

HP OMNIBOOK 3000, Service Manual

Search results

Summary of Contents for OMNIBOOK 3000

Reviews:

Related manuals for OMNIBOOK 3000

Brands by name

Popular brands