HP 81200 User Manual Download Page 81

Page: 81 / 240

Items of the Main Menu

Structure of the User Interface

HP 81200 Data Generator/Analyzer Platform User Guide, Revision 2.1

System Menu

The System menu has functions for testing the system’s integrity. These

tests can be performed at any time, as long as no test is running.

Note that the optional Diagnostics software package provides additional

tests which in case of problems can identify defective field replaceable

units.

System Selftests

Provides a window, from which the complete selftest or subsets can be

started. Ensures that all modules respond. Returns the current firmware

revisions of the modules and the identification numbers of installed

frontends.

Module Selftest

Enables you to check all or single modules. Checks the frontends built into

the modules and may take a minute.

Power On Test

Is automatically performed at power on. Checks all modules.

BIOS Revisions

Returns the current firmware revisions of the modules.

Dump Configuration

Enables you to write the current system configuration to a file. You have to

specify the path and file name.

The file will receive a contiguous string of ASCII characters, showing the

identification of all modules and frontends.

Window Menu

The Window menu contains standard functions provided by Microsoft

Windows. You can switch from one window to another.

Shortcut for switching windows: Ctrl + F6

Cascade

Superimposes all active windows. You can click any window title to bring

that window to the front.

Summary of Contents for 81200

















































































































































































































































Search results

Summary of Contents for 81200

Reviews:

HP 81200, User Manual, Page: 81 / 240

Search results

Summary of Contents for 81200

Reviews: