HP 520 5/XX Technical Reference Manual Download Page 90 | Manualshive

Page: 90 / 146

background image

90

4 Summary of the HP/Phoenix BIOS

HP/Phoenix BIOS (BIOS version: GX.07.xx)

I/O Addresses Used by the System (BIOS version: GX.07.xx)

Peripheral devices, accessory devices and system controllers are accessed
via the system I/O space. The 64 KB of addressable I/O space comprises 8-bit
and 16-bit I/O ports (these are registers that are located in the various
system components). When installing an expansion card, ensure that the
I/O address space selected is in the free area of the space reserved for
expansion cards (100h to 3FFh).

Refer to the BIOS I/O Port Map (BIOS version: GX.07.xx), on page 91 for
more detailed information.

System Memory Map (BIOS version: GX.07.xx)

Reserved memory used by expansion cards must be located in the area from
C8000h to EFFFFh.

100h-109h

HP reserved

15Ch-15Dh

I/O controller

170h-177h, 376h

IDE controller secondary channel

1F0h-1F7h, 3F6h

IDE controller primary channel

278h-27Fh, 378h-37Fh

Parallel port

2E8h-2EFh, 2F8h-2FFh, 3E8h-3EFh, 3F8h-3FFh

Serial port

370h-371h

Integrated I/O Controller

3B0h-3DFh

Integrated video graphics controller

3F0h-3F5h, 3F7h

Integrated floppy disk drive controller

496h-497h

HP reserved

678h-67Bh

Parallel port if ECP mode is selected

778h-77Bh

Parallel port if ECP mode is selected

00000h - 9FFFFh

640 KB

–

Base Memory Area

A0000h - BFFFFh

128 KB

–

Video Memory

C0000h - C7FFFh

32 KB

–

Video BIOS

C8000h - DFFFFh

96 KB

–

Expansion Cards Memory

E0000h - EFFFFh

64 KB

–

Available

F0000h - FFFFFh

64 KB

–

System BIOS

100000h - FFFFFFFFh

1 MB plus

–

Extended Memory

«
...
88
89
90
91
92
...
»

Summary of Contents for 520 5/XX



















































































































































Reviews:

No comments

Related manuals for 520 5/XX

Brand: National Instruments Pages: 93

Brand: IBM Pages: 770

st5548 - Thin Client

Brand: Compaq Pages: 39

Brand: FabiaTech Pages: 65

Brand: Aaeon Pages: 44

Power Panel 300

Brand: B&R Industries Pages: 612

Height Adjustable Standing Desk 4-Leg

Brand: Uplift Desk Pages: 7

Brand: MSI Pages: 85

OptiPlex 5070 Micro

Brand: Dell Pages: 34

Brand: TAG Pages: 6

Brand: Sinocan Pages: 41

Brand: Gispen Pages: 6

Brand: werma Pages: 2

Brand: Moxa Technologies Pages: 65

Brand: Diablotek Pages: 13

Valerus Shadow Elite Client Workstation Micro Form Factor

Brand: Vicon Pages: 2

Brand: Nexcom Pages: 48

Brand: Nexcom Pages: 61

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands