HP 520 5/XX Technical Reference Manual Download Page 126

Page: 126 / 146

126

5 Video Controllers

The Integrated Ultra VGA Video Controller

VESA Connector

The Video Electronics Standards Association (VESA) defines a standard
video connector, variously known as the VESA

feature

connector,

auxiliary

connector, or

pass-through

connector. The integrated video

controller supports an output-only VESA

feature

connector. This connector

is integrated directly on the system board, and is connected directly to the
pixel data bus and the synchronization signals.

To use the VESA feature connector in DOS, or Windows 95, the FCON.EXE
utility must be executed. This utility configures the system.

WARNING

Use of the VESA feature connector will disable the 1 MB video
memory upgrade, if this has been installed. Only the standard 1 MB
of video memory will be used.

Summary of Contents for 520 5/XX



















































































































































Search results

Summary of Contents for 520 5/XX

Reviews:

Related manuals for 520 5/XX

Brands by name

Popular brands

HP 520 5/XX, Technical Reference Manual

Search results

Summary of Contents for 520 5/XX

Reviews:

Related manuals for 520 5/XX

Brands by name

Popular brands