HP 520 5/XX Technical Reference Manual Download Page 139

Page: 139 / 146

English

139

6 Aztech AT3300 Audio Fax/Data Modem

European Firmware and Telephone Line Configuration

Enter the letter that corresponds to the country to be configured.

The message,

“Please wait, reprogramming the modem”

will be displayed while the Audio Fax/Data Modem is
reconfigured.

A window will then be displayed, indicating the modem firmware
country code that has been set for the selected country, and the
jumper block color setting.

To leave the Aztech AT3300 Localisation Utility:

Remove the Aztech AT3300 Localisation Utility floppy disk.

and

to reboot the PC.

SELECT THE COUNTRY:

A
B
C
D

E
F

G
H

Belgium
Denmark
Finland
France
Germany
Italy
Netherlands
Norway
Portugal
Spain
Sweden
Switzerland
United Kingdom

Quit

which country

→

Summary of Contents for 520 5/XX



















































































































































Search results

Summary of Contents for 520 5/XX

Reviews:

Related manuals for 520 5/XX

Brands by name

Popular brands

HP 520 5/XX, Technical Reference Manual

Search results

Summary of Contents for 520 5/XX

Reviews:

Related manuals for 520 5/XX

Brands by name

Popular brands