HP 520 5/XX Technical Reference Manual Download Page 53

Page: 53 / 146

2 System Board - (SiS Chipset) (Part Number: D4051-63001)

Devices on the ISA Bus

Feature Summary

Function

Features

Floppy disk controller

❒

Software compatible with the DP8473, the 765A, and the
N82077

❒

16-byte FIFO (default disabled)

❒

Burst and non-burst modes

❒

Perpendicular recording drive support

❒

New high-performance internal digital data separator (no
external filter components required)

❒

Low-power CMOS with enhanced power-down mode

❒

Automatic media-sense support

UARTs

❒

Software compatible with the PC16550A and PC16450

❒

A modifiable address that is referenced by a 16-bit programma-
ble register.

❒

13 IRQ channel options.

❒

Shadow register support for write-only bits.

❒

Four 8-bit DMA options for UART2.

Bidirectional parallel port

❒

Enhanced Parallel Port (EPP) compatible

❒

Extended Capabilities Port (ECP) compatible

❒

Bidirectional under either software or hardware control

❒

Demand mode DMA support.

❒

Selection of internal pull-up or pull-down resistor for Paper End
(PE) pin.

❒

Reduction of PCI bus utilization by supporting a demand DMA
mode mechanism and a DMA fairness mechanism.

❒

Includes protection circuit against damage caused when printer
is switched on, or operated at higher voltages.

❒

Output buffers that can sink and source 14 mA.

Three general purpose pins for three
separate chip select signals

❒

Programmed for game port control.

❒

Chip Select 0 (CS0) signal produces open drain and is powered
by the V

CCH

❒

Chip Select 1 (CS1) and 2 (CS2) signals have push-pull buffers
and are powered by the main V

❒

Decoding of chip select signals depends on the address and the
Address Enable (AEN) signal, and can be qualified using the
Read (RD) and Write (WR) signals.

Enhanced power management

❒

Special configuration registers for power down

❒

Reduced current leakage from pins.

❒

Low-power CMOS technology.

❒

Ability to shut off clocks to all modules.

Summary of Contents for 520 5/XX



















































































































































Search results

Summary of Contents for 520 5/XX

Reviews:

Related manuals for 520 5/XX

Brands by name

Popular brands

HP 520 5/XX, Technical Reference Manual

Search results

Summary of Contents for 520 5/XX

Reviews:

Related manuals for 520 5/XX

Brands by name

Popular brands