HP 520 5/XX Technical Reference Manual Download Page 41

Page: 41 / 146

2 System Board - (SiS Chipset) (Part Number: D4051-63001)

SiS Chipset

Processor Socket (D4051-63001)

The microprocessor is packaged in a pin-grid-array (PGA), which is seated
on the system board in a zero-insertion-force (ZIF) socket.

Memory Sockets (D4051-63001)

There are six main memory module sockets available with the HP Vectra 500
Series minitower and desktop computers. The sockets are arranged in three
banks (A to C), allowing memory installation up to a maximum of 192 MB.

The following illustration shows the physical layout of the memory bank
organization.

J10

SIMM Socket 6 (C2)

SIMM Socket 5 (C1)

Bank C

SIMM Socket 4 (B2)

SIMM Socket 3 (B1)

Bank B

J14

SIMM Socket 2 (A2)

J13

SIMM Socket 1 (A1)

Bank A

Summary of Contents for 520 5/XX



















































































































































Search results

Summary of Contents for 520 5/XX

Reviews:

Related manuals for 520 5/XX

Brands by name

Popular brands

HP 520 5/XX, Technical Reference Manual

Search results

Summary of Contents for 520 5/XX

Reviews:

Related manuals for 520 5/XX

Brands by name

Popular brands