HP 520 5/XX Technical Reference Manual Download Page 82 | Manualshive

Page: 82 / 146

background image

82

4 Summary of the HP/Phoenix BIOS

Overview

Overview

The information concerning the different versions of the HP/Phoenix BIOS
installed on the HP Vectra 500 Series models described in this chapter is
divided into two main sections:

•

The system BIOS identified by the version number

GX.07.xx,

installed on

the HP Vectra 500 Series PC models with an HP Service Part Number:
D4051-63001. For a complete list of the computers associated with this
part number, refer to “D4051-63001 Models” on page 15.

•

The system BIOS identified by the version number

GJ.07.xx

installed on

t

he HP Vectra 500 Series PC models with the HP Service Part Numbers:

D3657-63001 and D3661-63001. For a complete list of the computers
associated with these part numbers, refer to “D3657-63001 Models” on
page 16 and “D3661-63001 Model” on page 17.

HP/Phoenix BIOS Description

The System ROM contains the system BIOS (including the boot code, the
ISA and PCI initialization, DMI, the

Setup

program and the Power-On Self-

Test routines, plus their error messages).

The PC uses 128 KB of 200ns, Flash EEPROM implemented within a single
256 K

✕

8-bit ROM chip. This is a ROM that can be returned to its

unprogrammed state, by the application of appropriate electrical signals to
its pins, and then reprogrammed with the latest upgrade firmware.

Updating the System ROM

The System ROM can be updated with the latest BIOS firmware. It can be
ordered from HP or downloaded from one of the HP online services.

The System ROM is updated by running the PHLASH utility,

PHLASH.EXE

,

which is supplied with the BIOS upgrade file,

NN07xx.FUL

, and the system

definition file,

platform.bin

. You must specify the

model number

of the

PC since the utility which is supplied for a different model cannot be used
with this one. It must be run from a diskette.

«
...
80
81
82
83
84
...
»

Summary of Contents for 520 5/XX



















































































































































Reviews:

No comments

Related manuals for 520 5/XX

Brand: Xerox Pages: 20

Brand: Vector Graphic Pages: 40

Brand: Aaeon Pages: 43

Brand: Acer Pages: 101

Brand: Acer Pages: 28

Brand: Genesis Pages: 14

Alienware Area-51m R2

Brand: Dell Pages: 21

Alienware Aurora R13

Brand: Dell Pages: 20

Alienware Aurora R11

Brand: Dell Pages: 20

Alienware Aurora R3

Brand: Dell Pages: 70

Alienware Area-51 ALX

Brand: Dell Pages: 7

Alienware Aurora - R2

Brand: Dell Pages: 17

Brand: Dell Pages: 240

Alienware Area-51m R2

Brand: Dell Pages: 94

Alienware 0JYTRGA00

Brand: Dell Pages: 68

ALIENWARE AURORA

Brand: Dell Pages: 117

Alienware Aurora R11

Brand: Dell Pages: 109

Alienware Area-51 ALX

Brand: Dell Pages: 103

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands