HP 520 5/XX Technical Reference Manual Download Page 103

Page: 103 / 146

103

4 Summary of the HP/Phoenix BIOS

HP/Phoenix BIOS (BIOS version: GJ.07.xx)

Summary Configuration Screen (BIOS version: GJ.07.xx)

You can press

while the initial “Vectra” logo screen is being displayed to

run the

Setup

program (as described in the previous sub-sections).

Alternatively, you can press

to view the summary configuration screen.

This is displayed for a few seconds only, but it is possible to “freeze” it so the
configuration can be checked. Press the Pause/Break key to “freeze” the
summary screen.

The following summary screen is an example of a system configuration.

CPU [133 MHz]

: Pentium

System Rom

: F0DC - FFFF

Coprocessor

: Installed

BIOS Version

: GJ.07.17

System RAM

: 640 Kb

COM Ports

: 03F8, 02F8, 03E8

Extended RAM

: 7168 Kb

LPT Ports

: 02D8

Shadow RAM

: 384 Kb

Display Type

: EGA \ VGA

Cache RAM

: None

PS/2 Mouse

: Installed

Hard Disk 0

: 544 Mb

Diskette A

: 1.44 MB

Hard Disk 1

: None

Diskette B

: None

Hard Disk 2

: None

Flexible Disk B

: None

Hard Disk 3

: None

Summary of Contents for 520 5/XX



















































































































































Search results

Summary of Contents for 520 5/XX

Reviews:

Related manuals for 520 5/XX

Brands by name

Popular brands

HP 520 5/XX, Technical Reference Manual

Search results

Summary of Contents for 520 5/XX

Reviews:

Related manuals for 520 5/XX

Brands by name

Popular brands