HP 520 5/XX Technical Reference Manual Download Page 43

Page: 43 / 146

2 System Board - (SiS Chipset) (Part Number: D4051-63001)

Backplane (D4051-63001)

Minitower Backplane

The HP Vectra 500 Series minitower backplane supports three 16-bit ISA
(Industry Standard Architecture) cards, two 32-bit PCI (Peripheral
Component Interconnect) cards and has one combination slot for an ISA or
PCI card.

The six expansion card slots are arranged as follows:

•

Slot 1 - (the innermost) Combination slot that can be used for a
half-length 16-bit ISA card (15 cm / 6 inches) or a 32-bit PCI card.

•

Slot 2 - can be used for a 32-bit PCI card.

•

Slot 3 - can be used for a 32-bit PCI card.

•

Slot 4 - can be used for a full-length 16-bit ISA card (30 cm / 12 inches).

•

Slot 5 - can be used for a full-length 16-bit ISA card (30 cm / 12 inches).

•

Slot 6 - can be used for a full-length 16-bit ISA card (30 cm / 12 inches).

3 x ISA

2 x PCI

1 x ISA/PCI

Combination Slot

System Board

Connector

Slot 3

Slot 2

Slot 1

Slot 4

Slot 5

Slot 6

Summary of Contents for 520 5/XX



















































































































































Search results

Summary of Contents for 520 5/XX

Reviews:

Related manuals for 520 5/XX

Brands by name

Popular brands

HP 520 5/XX, Technical Reference Manual

Search results

Summary of Contents for 520 5/XX

Reviews:

Related manuals for 520 5/XX

Brands by name

Popular brands