Honeywell TotalPlant LCN System Installation Download Page 97 | Manualshive

Page: 97 / 132

background image

LCN System Installation

A-9

9/96

A.7

This is an example of cabling for Enhanced Redundant Application Modules using
K4LCN/EAMR boards as shown in Figures A-9 through A-16. The boards can be
installed in either node position of the Dual Node Module. There are four combinations of
upper/lower node positions.

51092

Front View

Fan

Lower Node P.S.

EAMR (51401996-100)
K4LCN (51401946-100)

Fan

EAMR (51401996-100)
K4LCN (51401946-100)

Interface Cable
(51304197-200)

MP-DNCF01

Figure A-9 — Redundant Application Module Cabling (K4LCN/EAMR)

Figure A-9 and A-10 show front and back views of the same application.

51093

KLCN CA (51304542)

AMR Cable (51304198)

AMR I/O (51304159)

KLCN CB (51304544)

KLCN CB (51304544)

Rear View

KLCN CA (51304542)

Figure A-10 — Redundant Application Module Cabling (K4LCN/EAMR)

«
...
95
96
97
98
99
...
»

Summary of Contents for TotalPlant LCN





































































































































Reviews:

No comments

Related manuals for TotalPlant LCN

Professional Series

Brand: PACOM Pages: 15

Netlink FRX4000

Brand: Cabletron Systems Pages: 8

Brand: Cabletron Systems Pages: 4

MMAC-Plus 9F106-02

Brand: Cabletron Systems Pages: 7

Brand: Data Translation Pages: 60

Brand: LaCie Pages: 44

LaCie Ethernet Disk

Brand: LaCie Pages: 2

SATA II ExpressCard 34

Brand: LaCie Pages: 2

12big Rack Fibre 8

Brand: LaCie Pages: 9

WS-650 lite Series

Brand: Laurell Pages: 84

Brand: Ubee Pages: 9

Brand: IBA Pages: 33

Brand: SyChip Pages: 24

Brand: Seattle Computer Products Pages: 31

AT-8550/SP Series

Brand: Allied Telesis Pages: 114

Brand: Belkin Pages: 57

Brand: Advantech Pages: 68

Brand: Promise Technology Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands