Honeywell TotalPlant LCN System Installation Download Page 120

Page: 120 / 132

LCN System Installation

C-8

9/96

C.6

Micro TDC 3000 Cabling

Scope

Cabling for a Micro TDC 3000 is shown in the following figure and table.
The number in the circles refers to the line item in the table below.

Figure C-8

Micro TDC 3000 Cabling—Standard

53418

Engineering
Keyboard

Enclosure

Operator Keyboard

Monitor

Printer

Cartridge Drive 0

EPDGC I/O

Touchscreen

Power Supply
or Five-slot
Module J8

Cartridge Drive 1

Control

Keyboard

SCSI

Printer

Cursor

Video

Table C-7

Micro TDC 3000 Cabling—Standard (Trackball)

Ref. #

Part Number

Application Notes

51192126-200

Video Cable

51308099-100

Mouse/Trackball Interface Cable

Not Applicable

51308103-003

Printer Cable – 3 meters/9.8 ft.

51308103-008

Printer Cable – 8 meters/26.3 ft.

51308103-015

Printer Cable – 15 meters/49.2 ft.

51192054-101

Cable, SCSI Shielded, 50 position

51305070-200

Cable, SCSI

51308110-100

Cartridge DC Power Cable

51308109-100

Cartridge DC Power Cable (in enclosure)

51308105-200

Keyboard Interface Cable

51308104-100

Keyboard Interface Cable (in keyboard tray)

51304496-046

Engineer’s Keyboard Cable (in keyboard tray)

Continued on next page

Summary of Contents for TotalPlant LCN





































































































































Search results

Summary of Contents for TotalPlant LCN

Reviews:

Related manuals for TotalPlant LCN

Brands by name

Popular brands

Honeywell TotalPlant LCN, System Installation

Search results

Summary of Contents for TotalPlant LCN

Reviews:

Related manuals for TotalPlant LCN

Brands by name

Popular brands