Honeywell TotalPlant LCN System Installation Download Page 118

Page: 118 / 132

LCN System Installation

C-6

9/96

C.4

Universal StationX Cabling—Classic Furniture

Scope

Cabling for Universal StationX in classic furniture is shown in the
following figure and table.

Figure C-6

UXS Cabling—Classic Furniture with Touchscreen and Mouse/Trackball

53414

Engineering
Keyboard

Enclosure

J7
J10
Keyboard Assy

Keylock Assy

Annunciator
Relay Panel

Monitor

Touch Screen

Printer

Cartridge Drive 0

DAT Drive 1

TPDGC I/O

Video

Cursor

Printer

SCSI

Keyboard

Fan

Power Supply

J5
J6

Distribution Box

Mouse/Trackball

AC Distribution

HDDT I/O

Module J5

Table C-5

Universal StationX Cabling—Classic Furniture

Ref. #

Part Number

Application Notes

51191784-100

Cable, CRT Signal

51308119-100

TPDGC I/O Distribution Box Cable

51308123-100

EC Smartscreen Cable

51308103-003

Printer Cable – 3 meters/9.8 ft.

51308103-008

Printer Cable – 8 meters/26.3 ft.

51308103-015

Printer Cable – 15 meters/49.2 ft.

51192054-102

Cable, SCSI Shielded, 50 position

51305070-100

Cable, SCSI

Not Applicable

51192054-102

Cable, SCSI, Shielded, 50 Pos

51305070-200

Cable, SCSI

51308094-600

Classic Module AC Power Cable

51308051-200

P.S. Enclosure DC Cable

51308052-200

P.S. Enclosure AC Cable

51308055-100

Drive Cable DC Power

51303420-586

Module Status Cable

51308126-100

Keyboard Cable

51304496--026

Engineering Keyboard Interface Cable

51304047-652

Annunciator Power Cable

51304029-500

Keylock Switch Cable

Summary of Contents for TotalPlant LCN





































































































































Search results

Summary of Contents for TotalPlant LCN

Reviews:

Related manuals for TotalPlant LCN

Brands by name

Popular brands

Honeywell TotalPlant LCN, System Installation

Search results

Summary of Contents for TotalPlant LCN

Reviews:

Related manuals for TotalPlant LCN

Brands by name

Popular brands