manualshive.com logo in svg

Honeywell TotalPlant LCN, System Installation

Share
Download
Honeywell TotalPlant LCN System Installation Download Page 87

LCN System Installation

16-3

9/96

16.6

16.6  CONNECTION TO A PRINTER

ESD Wrist Strap

Use ESD

Wrist Strap

   Use an ESD Wrist Strap grounded to the electronics chassis when

connecting or disconnecting cables.

A single laser or matrix printer can be connected to the PARALLEL port on the rear panel
of the electronics.  A laser printer can be placed on an adjacent work surface.  If a Signum
printer is used, it must be placed on a pedestal or other supporting device.

STOP!

    Do not proceed until you have completed the configuration function detailed in

the Configurator.  The LCN node number is software-configured and may conflict with
another node until it is correctly configured.  If you proceed to connect the LCN cables,
parts of the LCN can become ISOLATED.

16.7  LCN CABLE CONNECTION

The LCN A and LCN B cables must follow the installation rules for cable length and
installation practices found in subsection 3.6.

The two LCN coax cables connect to an LCN Media Access Unit (MAU) with coax Tee’s.
The MAU is connected to the port on the LCNP board located in the middle slot (Slot 3) in
the electronics module.  The MAU is located in the cable cavity of the console station.  See
Figures 16-3, 16-4, and 16-5 for the various mount schemes.

The following illustration shows the cabling connection of the LCN A and LCN B cables to
the MAUs, as well as the MAU cable connection to the LCNP board.

LCNP

Cable A

Cable B

LCNP/MAU Coax Connection

15157

LCN MAU Cable
51305313-100

Figure 16-3 — Connection of LCN Cable A and Cable B to the LCN MAU

Summary of Contents for TotalPlant LCN





































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands