Honeywell TotalPlant LCN System Installation Download Page 36

Page: 36 / 132

LCN System Installation

3-20

9/96

3.9

5. The peripheral cables are folded and retained by cable clamps inside the

worksurface cabinet.

For Classic furniture

• Unfasten the cable, still passing them through the cable clamp.

• Pass the cable through the cable pass-through hole in the

cabinet side, into the Universal Station (or Universal StationX)
cabinet.

• Connect the peripheral interface cable as follows:

– Cartridge cable, 51192054-102 to the EPDGC or TPDGC

I/O board SCSI connector J2.

For Ergonomic furniture

• The cables are stored in the foot of the worksurface furniture.

Free the cable and pass the cable through the cable pass-through
hole in the cabinet side, into the Universal Station (or Universal
StationX) cabinet.

• Run the interface cable up the left side of the console leg to the

I/O card file.

• Connect the peripheral interface cable(s) as follows:

– Cartridge cable, 51192054-102 to the EPDGC or TPDGC

I/O board SCSI connector J2.

6. If there is any excess cable hanging below the cabinet, pull it into the single bay

cabinet and fasten it in the cable clamps on the side of the cabinet.

Summary of Contents for TotalPlant LCN





































































































































Search results

Summary of Contents for TotalPlant LCN

Reviews:

Brands by name

Popular brands

Honeywell TotalPlant LCN, System Installation

Search results

Summary of Contents for TotalPlant LCN

Reviews:

Brands by name

Popular brands