Honeywell TotalPlant LCN System Installation Download Page 121

Page: 121 / 132

LCN System Installation

C-9

9/96

C.6

Micro TDC 3000 Cabling,

Continued

Touchscreen option

Cabling for a Micro TDC 3000 is shown in the following figure and table.
If the touchscreen special has been installed, the following figure and table
represents the cabling. The number in the circles refers to the line item in
the table below.

Figure C-9

Micro TDC 3000 Cabling—Touchscreen

53418

Engineering
Keyboard

Enclosure

Operator Keyboard

Monitor

Printer

Cartridge Drive 0

EPDGC I/O

Video

Cursor

Printer

SCSI

Keyboard

Touch Screen

Power Supply
or Five-slot
Module J8

Cartridge Drive 1

Control

Table C-8

Micro TDC 3000 Cabling—Touchscreen

Ref. #

Part Number

Application Notes

51192126-200

Video Cable

51308097-100

Touchscreen Interface Cable

51308114-100

Touchscreen Interface Cable

51308103-003

Printer Cable – 3 meters/9.8 ft.

51308103-008

Printer Cable – 8 meters/26.3 ft.

51308103-015

Printer Cable – 15 meters/49.2 ft.

51192054-101

Cable, SCSI Shielded, 50 position

51305070-200

Cable, SCSI

51308110-100

Cartridge Drive Power Cable

51308109-100

Cartridge Drive Power Cable (in enclosure)

51308105-200

Keyboard Interconnecting Cable

51308104-100

Keyboard Interface Cable (in keyboard tray)

51304496-046

Engineer’s Keyboard Cable (in keyboard tray)

Summary of Contents for TotalPlant LCN





































































































































Search results

Summary of Contents for TotalPlant LCN

Reviews:

Related manuals for TotalPlant LCN

Brands by name

Popular brands

Honeywell TotalPlant LCN, System Installation

Search results

Summary of Contents for TotalPlant LCN

Reviews:

Related manuals for TotalPlant LCN

Brands by name

Popular brands