Honeywell TotalPlant LCN System Installation Download Page 122

Page: 122 / 132

LCN System Installation

C-10

9/96

C.7

Applications ModuleX (AXM) Cabling

Scope

Cabling for Applications ModuleX (AXM) mounted in classic furniture is
shown in the following figure and table. The number in the circles refers to
a line item in the table below.

Figure C-10

AXM Cabling in Classic Furniture

53419

Enclosure

CD ROM Drive 0

(optional)

HDDT I/O

AC Power
Distribution
Box

DAT Drive 1

(optional)

Power

Supply

Fan

Table C-9

AXM Cabling in Classic Furniture

Ref. #

Part Number

Application Notes

51192054-102

Cable, SCSI Shielded, 50 position

51305070-100

Cable, SCSI

51308094-600

Classic Module AC Power Cable

51308052-200

DC Power Cable, Power Supply End

51308055-100

DC Power Cable, Cartridge End

51308051-200

DC Power Cable, Fan

Summary of Contents for TotalPlant LCN





































































































































Search results

Summary of Contents for TotalPlant LCN

Reviews:

Related manuals for TotalPlant LCN

Brands by name

Popular brands

Honeywell TotalPlant LCN, System Installation

Search results

Summary of Contents for TotalPlant LCN

Reviews:

Related manuals for TotalPlant LCN

Brands by name

Popular brands