Honeywell TotalPlant LCN System Installation Download Page 76

Page: 76 / 132

LCN System Installation

14-4

9/96

14.7

ESD Wrist Strap

Use ESD

Wrist Strap

Use an ESD Wrist Strap grounded to the Minitower chassis when

connecting or disconnecting cables.

14.7.2 Connecting the Optional Integrated Keyboard and Mouse

1. Connect the 15-pin cable connector to the Keyboard connector (right-hand) on the face

plate of the left-most ISA card slot.

2. Connect the Mouse Cable 9-pin connector to the Mouse miniature DIN connector on the

rear of the minitower.

3. Connect the jumper cable, 51305381-100, to the IKBI2 board in slot 5 (left-most slot)

and to the rear panel connection labeled “KB.”

16222

IKB

Cursor

IKBI2

Mother

Board

Mouse

MiniTower

IKBI PS/2 KB Cable

51305381-100

Keyboard

Interface

Figure 14-2 — Integrated Keyboard/Mouse Cable Connections to Rear Panel

14.8 CONNECTING THE OPTIONAL TOUCHSCREEN

Connect the free end of the touchscreen cable to the connector in Slot 4 (second slot from
the left).

14.9 CONNECTION TO THE ETHERNET

An adapter, 51191782-100, is connected to the Ethernet connector on the back of the
electronic tower. This adapter connects to the 10base-5 Ethernet or a 10base-2 Ethernet.

If a 10base-T Ethernet is used, the cable from the hub is connected to the RJ-45 connector
on the rear panel.

Summary of Contents for TotalPlant LCN





































































































































Search results

Summary of Contents for TotalPlant LCN

Reviews:

Brands by name

Popular brands

Honeywell TotalPlant LCN, System Installation

Search results

Summary of Contents for TotalPlant LCN

Reviews:

Brands by name

Popular brands