Honeywell S7999D SOLA User Manual Download Page 18

Page: 18 / 52

65-0315—02

Warm Weather Shutdown

Configuration

Table 13 displays Warm Weather Setpoint configuration

parameters.

Demand Priority Configuration

Parameters

Fig. 34 displays R7910 Hydronic Control Demand Priority

configuration options. Press the arrows to change the priority

order.

Fig. 34. Demand priority configuration.

MODULATION Configuration

Parameters

Table 14 displays R7910 Hydronic Control Modulation

configuration parameters.

Fig. 35. Modulation configuration.

Steam Modulation Configuration

Parameters

Table 15 displays R7911 Steam Modulation Configuration

parameters.

Table 13. Warm Weather Setpoint

Configuration Parameters.

Parameter

Comment

Enable

Enabled, disabled

Setpoint

-40 °F to 266 °F (-40 °C to 130 °C)

Table 14. R7910 Hydronic Control Modulation Configura-

tion Parameters.

Parameter

Comment

CH maximum

modulation rate

RPM or %

DHW maximum

modulation rate

RPM or %

Minimum modulation

rate

RPM or %

CH forced rate time

0-600 seconds

CH forced rate

RPM or %

DHW forced rate time 0-600 seconds
DHW forced rate

RPM or %

CH slow start enable Enabled

Disabled

DHW slow start

enable

Enabled

Disabled

Slow start degrees

0 °F to 180 °F (-17 °C to 82 °C)

Slow start ramp

RPM /minute or %/minute

0-10/4-20 mA Output

hysteresis

Table 15. R7911 Steam Modulation Configuration

Parameters.

Parameter

Comment

CH maximum

modulation rate

RPM or %

Minimum modulation

rate

RPM or %

CH forced rate time

0-600 seconds

CH forced rate

RPM or %

0-10/4-20 mA Output

hysteresis

Summary of Contents for S7999D SOLA





















































Search results

Summary of Contents for S7999D SOLA

Reviews:

Related manuals for S7999D SOLA

Brands by name

Popular brands

Honeywell S7999D SOLA, User Manual

Search results

Summary of Contents for S7999D SOLA

Reviews:

Related manuals for S7999D SOLA

Brands by name

Popular brands