background image

The service technician is required to read and follow the “Safety Precautions” and “Important Safety Notice” in the Main Manual.

Service Manual

Copyright 2001 by Matsushita Electric Corporation of
America. All rights reserved. Unauthorized copying
and distribution is a violation of law.

ORDER NO. MTNC010417C1

B2

®

(P5P)

Main Manual

Panasonic

PT-51HX41E

AP820

PT-51HX41CE

AP820

PT-56HX41E

AP820

PT-56HX41CE

AP820

PT-61HX41E

AP820

PT-61HX41CE

AP820

Chassis

Models

HDTV MONITOR

WARNING! This Service Manual is designed for experienced repair technicians only and is not designed for use by the general public.
It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product.
Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any attempt to
service or repair the product or products dealt with in this Service Manual by anyone else could result in serious injury or death.” 

This Service manual is issued as a service guide for the models of the P5P family listed above. Included in this manual
are a set of schematics, alignment procedures, disassembly procedures and a complete parts list.

Summary of Contents for PT51HX41E - 51" PROJECTION TV






























































Reviews: