Honeywell S7999D SOLA User Manual Download Page 15

Page: 15 / 52

65-0315—02

Central Heat Parameters

(R7910 Hydronic Control Only)

Table 7 displays Central Heat Hydronic Control configuration

parameters.

Fig. 31. Central Heat hydronic configuration.

Table 6. System Identification Information.

Status

Comment

Product Type

Type of product that the burner is

OS Number

Model number associated with burner

Software Version

Version of software running in the

R7910 or R7911

Date Code

Date when R7910 or R7911 was

assembled

Application Revision Version of application data in the

R7910 or R7911

Safety Revision

Revision of safety data in the R7910

or R7911

Table 7. Central Heat Hydronic

Configuration Parameters.

Parameter

Comment

CH enable

Disable or Enable Central Heating

Loop

Demand switch

Sensor for Central Heat demand:

Sensor only

Sensor & STAT terminal

Sensor & Remote Stat

LCI & Sensor

Outdoor reset

Enabled

Disabled

CH has priority over

Lead Lag

Yes, No, Cancel

Setpoint source

Local

S2 (J8-6) 4-20mA

Setpoint

Setpoint for normal Central Heat

modulation:

32 °F to 250 °F (0 °C to 120 °C)

Time of day setpoint Setpoint when Time Of Day switch is

on. 32 °F to 250 °F (0 °C to 120 °C)

Off hysteresis

Differential above setpoint when boiler

is turned off.

2 °F to 234 °F (-16 °C to 112 °C)

On hysteresis

Differential from setpoint when boiler

is turned on.

2 °F to 234 °F (-16 °C to 112 °C)

4 mA water

temperature

-40 °F to 266 °F (-40 °C to 130 °C)

20 mA water

temperature

-40 °F to 266 °F (-40 °C to 130 °C)

Modulation sensor

Outlet sensor, Inlet sensor, S5 (J8-11)

Modulation Rate

Sensor

Local

P-gain

Gain applied for the P portion of the

PID equation

0-400

I-gain

Gain applied for the I portion of the

PID equation

0-400

D-gain

Gain applied for the D portion of the

PID equation

0-400

Hysteresis step time Time between hysteresis step

changes: 0-600 seconds (0=Disable

hysteresis stepping)

Summary of Contents for S7999D SOLA





















































Search results

Summary of Contents for S7999D SOLA

Reviews:

Related manuals for S7999D SOLA

Brands by name

Popular brands

Honeywell S7999D SOLA, User Manual

Search results

Summary of Contents for S7999D SOLA

Reviews:

Related manuals for S7999D SOLA

Brands by name

Popular brands