manualshive.com logo in svg

Honeywell CGW-MB, Installation And User Manual, Page: 68 / 187

Share
Download
Honeywell CGW-MB Installation And User Manual Download Page 68

CGW-MB Installation and Users’ Manual | P/N:LS10248-000HW-E | REV.G | JUL/31/2022

67

Read Device Identification (0x2B/0x0E)

Modbus Communications

7.22.3  CLSS Gateway mainboard Information Input Registers

The CGW-MB records some status and configuration information for debugging and 
technical support purposes. This information is stored in some Reserved CLSS Gateway 
mainboard registers as outlined below.
•

CLSS Gateway mainboard Modbus Address

•

CLSS Gateway mainboard IP Address

•

CLSS Gateway mainboard Version Number

7.22.4  Node Status Details

Each nodes status is represented by a bit in a register. If the bit is set, the node is on line.

 

Below table provides an example of how this is represented in a register.

7.23  Read Device Identification (0x2B/0x0E)

This function code allows reading the identification and additional information about the 
CGW-MB.

NOTE: 

Information/debug values are used by the CGW-MB Unit ID only. All other nodes 

reject reads in this address range.

Table 7.33:  CLSS Gateway mainboard Information Input Register Addresses

Start Address

End Address

Description

360001

360100

Information/Debug information

320001

320015

Node Status:
1 = On Line
0 = Off Line
The CGW-MB tracks status of network nodes 
under Modbus feature monitoring.

360016

360016

CLSS Gateway mainboard major version 
number

360017

360017

CLSS Gateway mainboard minor version 
number

360018

360018

CLSS Gateway mainboard feature number

360019

360019

CLSS Gateway mainboard build number

Table 7.34:  Node Status Example

Bit Number

Address

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

0

320001

N16

N15 N14 N13 N12 N11 N10

N9

N8

N7

N6

N5

N4

N3

N2

N1

320002

N32

N31 N30 N29 N28 N27 N26 N25 N24 N23 N22 N21 N20 N19 N18 N17

Table 7.35:  Read Device Identification (Ox2B/OxOE)

Object 

ID

Object Name / 

Description

Value

0x00

VendorName

Notifier

0x01

ProductCode

1

0x02

MajorMinorRevision

V1.0 (

Example

)

0x03

VendorUrl

www.notifier.com

0x04

ProductName

Modbus CLSS 
Gateway mainboard

0x05

ModelName

Modbus CLSS 
Gateway mainboard

Summary of Contents for CGW-MB




























































































































































































Reviews:

No comments