manualshive.com logo in svg

Honeywell CGW-MB, Installation And User Manual, Page: 111 / 187

Share
Download
Honeywell CGW-MB Installation And User Manual Download Page 111

CGW-MB Installation and Users’ Manual | P/N:LS10248-000HW-E | REV.G | JUL/31/2022

110

CGW-MB Parts

The BACnet Feature

8.4  CGW-MB Parts

8.5  System Requirements

The CGW-MB can monitor up to 16 panels. All of these panels should have a combined 

maximum of 15,000 objects only. This includes all detectors, monitor modules, control 
modules, bell circuits, and so on. 
Refer to the panel manual for details about wiring limitations.
Access the configuration web page from a computer in the same IP subnet as the CGW-
MB with latest version of Google Chrome™. JAVA® version 6 or higher must also be 
installed and enabled.

8.6  System Architecture

These are connections options for the CGW-MB architecture.
An Internet or Intranet IP network connection is used with both architectures.

8.6.1  IP Restrictions for the CLSS Gateway mainboard

•

Assign a static IP address. 

•

Following are not supported:

• Web access through an HTTP proxy server 
• Use of a NAT (Network Address Translation)

Other 
Products

Unmonitored but network compatible.

• NCA-2
• NCD
• NWS-3
• BACNET-GW-3
• NFN-GW-PC-HNW-2 
• NFN-GW-EM-3
• PC NFN CLSS Gateway mainboards:

• NFN-GW-PC-F
• NFN-GW-PC-W
• NFN-GW-PC-HNMF
• NFN-GW-PC-HNSF
• NFN-GW-PC-HNW

• VESDA-HLI-GW

Table 8.1:  CLSS-Compatible Equipment List

Type

Equipment

Part Number 

Description 

 HON-CGW-MBB

 CGW-MB with enclosure

 CGW-MB

 CGW-MB board

 CGW-BB

 CGW-MB enclosure

 50160636-001

 CGW-MB kit. It includes a 30” NUP cable 

and a NOTIFIER lock and key set.

 32351718-001

 10 ft NUP Serial (RS-232) cable kit

NOTE: 

DHCP is supported, but not recommended. 

              Before using DHCP with LAN for Intranet connection, consult the network
              administrator of the Site.

Summary of Contents for CGW-MB




























































































































































































Reviews:

No comments