manualshive.com logo in svg

Honeywell CGW-MB, Installation And User Manual, Page: 45 / 187

Share
Download
Honeywell CGW-MB Installation And User Manual Download Page 45

CGW-MB Installation and Users’ Manual | P/N:LS10248-000HW-E | REV.G | JUL/31/2022

44

Agency Listings and Approvals

Modbus Communications

7.8  Agency Listings and Approvals

•

UL/ULC Listed: S35608

•

CSFM: 7300-1637:0504

•

FDNY: COA#000121, COA#000122

7.8.1  Agency Restrictions and Limitations

•

CGW-MB is UL 864 and ULC-S527 listed for supplementary use only.

7.9  Standards

Compliance 

This product has been investigated to, and found to be in compliance with, the following 
standards:

Underwriters Laboratories

•

UL 864 - Control Units for Fire Alarm Systems, Tenth Edition

Underwriters Laboratories Canada

•

CAN/ULC S527-19 - Standard for Control Units for Fire Alarm Systems, Fourth 

Edition

Installation 

This product is intended to be installed in accordance with the following:

Local

•

AHJ - Authority Having Jurisdiction

National Fire Protection Association

•

NFPA 70 - National Electrical Code

•

NFPA 72 - National Fire Alarm and Signaling Code

Underwriters Laboratories Canada

•

CAN/ULC S527 - Installation of Fire Alarm Systems

•

CAN/ULC S561 - Installation and Services for Fire Signal Receiving Centres and 

Systems

Canada

•

CSA C22.1 - Canadian Electrical Code, Part I, Safety Standard for Electrical 

Installations

Summary of Contents for CGW-MB




























































































































































































Reviews:

No comments