Honeywell CGW-MB Installation And User Manual Download Page 150

Page: 150 / 187

CGW-MB Installation and Users’ Manual | P/N:LS10248-000HW-E | REV.G | JUL/31/2022

149

ESSER Panels

Connecting to the Panels



Tools 8000 Settings for IQ8 Panels

1. Double click on

Serial Interface

in Tools 8000.

2. Select

RS-232

from the

Type of interface

list.

3. Select

Remote Access

from the

Device in use

list.

4. Click

Power Connection

Using a power cable, the CLSS Gateway mainboard can connect to the 12V power

supply module of the IQ8 panel.

On the CLSS Gateway mainboard Side

• Ensure that the RS-232 cable is connected in the RS-232 port of the CLSS Gateway

mainboard.

• Switch the S7 Switch next to the RS-232 port towards

NUP_IN

Figure C.10: The S7 Switch

NOTE:

Use the details given on the power supply module of the panel.

NOTE:

Although the CLSS Gateway mainboard is capable of receiving 24V DC power, it

can work with the 12V DC power of the IQ8 panel. Ensure that the power supply to the
CLSS Gateway mainboard is 12V DC power.

Summary of Contents for CGW-MB




























































































































































































Search results

Summary of Contents for CGW-MB

Reviews:

Honeywell CGW-MB, Installation And User Manual, Page: 150 / 187

Search results

Summary of Contents for CGW-MB

Reviews: