manualshive.com logo in svg

Honeywell CGW-MB, Installation And User Manual, Page: 178 / 187

Share
Download
Honeywell CGW-MB Installation And User Manual Download Page 178

CGW-MB Installation and Users’ Manual | P/N:LS10248-000HW-E | REV.G | JUL/31/2022

177

NOTIFIER® European Panels (EN)

Connecting to the Panels

3. Power Connection

The CLSS Gateway mainboard can receive its power either from an external power 

source or from the non-resettable internal power of the panel.For the External Power 

Supply:

On the CLSS Gateway mainboard Side

1. Connect to the 24V DC external power supply or to the panel’s 24V DC power port.
2. Ensure that the S7 switch next to the RS-232 port is switched towards 

NUP_OUT.

Figure C.29:  The S7 Switch

On the Panel Side

• Pearl Panels: At the S-BUS board in the ANN-BUS PRI terminal:

• Connect the RS-485 +ve wire to the A port.
• Connect the RS-485 -ve wire to the B port.

• INSPIRE Panels: In the serial communication card or in the I/O card, 

• Connect the Red wire to the pin 1 (Aux. DC OUT +24V).
• Connect the Black wire to the pin 2 (Aux. DC OUT GND).

External Power Supply
Use this option if the CLSS Gateway mainboard is 

not

 receiving the power from the 

panel.

• On the CLSS Gateway mainboard Side

Connect to the power port of the CLSS Gateway mainboard. 
Refer to 

Figure C.2

 where the power port on the CLSS Gateway mainboard is 

labeled as 7. It is the P2 pin on the CLSS Gateway mainboard board.

• On the External Power Supply Side

Connect to the 24V DC external power supply.

NOTE: 

The external power supply must be dedicated and not shared with any other 

devices.

NOTE: 

The panel’s power supply to the CLSS Gateway mainboard must be 24V DC 

power.

Summary of Contents for CGW-MB




























































































































































































Reviews:

No comments